Do-It-Yourself Ceramic Water Filter

Do-It-Yourself Ceramic Water Filter by The Architect

Years ago, while visiting the South American country of Peru, I was stunned to find that every drop of drinking water had to first be boiled, before it was considered safe to drink. In a country of 22 million people, I thought this an incredible waste of money and natural resources. There had to be a better way. On my return, I set out to design a cheap ceramic filter that could be easily constructed using simple components readily obtained from any hardware or box store.

(As a side note, on one of my trips to Peru, I was a bit careless. Suffice it to say that Montezuma has nothing on the Inca revenge.)

photo1

Components

Components required to make the ceramic filter include the following:

  • 1 piece of 8” long 2” schedule 40 PVC pipe
  • 2” dia. Doulton ceramic filter candle (or similar)
  • 2” PVC rounded end cap
  • 2” dia. female connector – threaded
  • 2” PVC end cap – threaded
  • 3’ ¼” I.D. plastic icemaker tubing
  • ¼” I.D. Hose Bib connector
  • 3/8” icemaker line connector
  • 2” I.D. x 1/8” thick rubber “O” ring
  • 5/8” I.D. spacers or washers

Tools

Tools and other items that will be required include the following:

photo2

The Filter Candle

The Doulton or British Berkefeld ceramic water filter has been in use around the world since 1827. It has been proven reliable in over 150 countries to remove up to 99.99 percent of common bio-pathogens. It can also be a bit expensive, costing about $250. I was lucky enough to find an entire case of old, delaminated filters on Ebay for $5 each, but a new filter can be purchased for about $25.

photo3

Construction

Before you begin, center drill a ½” hole in the threaded end cap. (This hole will have to be widened with a file to fit the filter post.) Also drill a 3/8” hole in the rounded end cap. Attach the Hose Bib and 3/8” connectors to the icemaker line (Photo 1).

photo4

  1. With the sandpaper, roughen any PVC surface that will receive glue (interior of end caps, and both exterior ends of 2” PVC pipe). Apply glue and immediately attach end cap. Seat securely. (You may use a rubber mallet, if one is available.) Glue and attach the remaining end cap. Let stand for 30 minutes to cure.
    photo5
  2. Slip rubber “O” ring around the filter barrel and work it upwards as far as it will go. (Note: Do not forget the “O” ring, as it is a crucial part of the assembly.)
    photo6
  3. Slide the filter candle (with “O” ring in place) into the finished PVC pipe assembly. Position spacers and/or washers onto the filter post, which should equal about 3/8” or more. Attach threaded end cap to PVC filter assembly. The end cap must be tight enough to apply sufficient pressure on the “O” ring to prevent infiltration of contaminated water. (To test the seal, shake the completed filter from side to side; if you hear the ceramic filter moving, you will need to add a washer or tighten the cap further.)
    photo7
  4. Apply thread tape to 3/8 connector, and then insert and secure it to the rounded end cap. (In the event that the filter seems to be blocked, you may need to back the 3/8” connector out a bit.)

Continue Reading/Survival Blog>>>

Sharing is caring!

Author Image

Survival Blog

Our IP Address: 64.92.125.116 primary 50.193.232.247 I’m James Wesley, Rawles (“JWR”), a survivalist author. I’m a former U.S. Army Intelligence officer and technical writer. I’m now a full-time novelist and part-time blogger and retreat consultant. I founded SurvivalBlog in 2005, and now serve as Senior Editor. Day-to-day operation of the blog is handled brilliantly by Hugh J. Latimer (“HJL”), our Managing Editor. (To contact JWR or HJL, see our Contact Page.) Because of SurvivalBlog, we are part of something bigger: a virtual community of some of the most brilliant people that you could ever meet. Despite our differences, we all have an interest in preparedness.